Succinonitrile Polarity

Is C₄H₄N₂ (Succinonitrile) Polar or Nonpolar? Molecular Polarity & Structure Analysis

Figure 1: 2D Lewis Structure (C ₄H ₄N ₂; tetrahedral carbon centre)

Polarity Parameters of C₄H₄N₂

CAS Registry Number	110-61-2
Molecular Formula	C4H4N2
Molecular Weight	80.09 g/mol
Valence Electrons	30
Lewis Structure Guide	View C4H4N2 Lewis Structure Guide
Dipole Moment (μ)	The lowest-energy conformer is centrosymmetric and has μ = 0 D exactly, but other conformers inside the thermally accessible window generated by the conformer search (within about 6 kcal mol⁻¹ of the minimum) carry up to ≈5.37 D; the Boltzmann-weighted ensemble dipole is ≈2.42 D, and the measured gas-phase value is a population average near it
Dielectric Constant (εr)	Not quoted — the Debye estimate would inherit a dipole that this method does not deliver reliably for this class of compound
Snyder Polarity Index (P′)	Not conventionally assigned
XlogP3-AA	0.81 (Crippen calculated, RDKit) (computed descriptor)

Note: Snyder P′ is a chromatographic solvent scale developed for conventional liquid solvents; no dipole magnitude is quoted: the method over-estimates nitriles (mean error +0.61 D over three benchmark nitriles), so the polarity verdict rests on symmetry and structure alone; no relative permittivity is quoted, because the Debye estimate would inherit an unreliable dipole; XlogP is a calculated partition descriptor, not a direct measure of solvent polarity.

1. Molecular Polarity Analysis of Succinonitrile: Geometry & Dipole Vector

To determine whether Succinonitrile (C₄H₄N₂) is polar or nonpolar, the decisive question is whether the bond dipoles of the molecule cancel once its three-dimensional shape is taken into account. Succinonitrile is a nitrile, built from 2 × nitrile (–C≡N). As set out in the C₄H₄N₂ Lewis Structure Guide, C₄H₄N₂ has 6 heavy atoms and 1 rotatable bond. Used in the production of plastics and nitron fibers..

The bond polarities follow from electronegativity. The largest differences in the structure are C–N (ΔEN ≈ 0.49), so electron density is pulled toward nitrogen. In three dimensions, the carbon centre is tetrahedral with sp3 hybridization and bond angles near 109.5°. As a result, the lowest-energy conformer is centrosymmetric and has μ = 0 D exactly, but polar conformers inside the thermally accessible window give a Boltzmann-weighted ensemble dipole of ≈2.42 D at 298 K, and the measured gas-phase value is a population average near it rather than the value of any single geometry. The dipole is conformation-dependent: across the low-energy conformers the calculation spans ≈0.00–5.37 D, and the value quoted above is the one for the lowest-energy conformer. For a flexible molecule the measured gas-phase dipole is the Boltzmann average over that population, so it lies between the two, not at either end.

For formulation and process work, the useful consequences are these: the calculated topological polar surface area is 47.6 Ų, 0 hydrogen-bond donors and 2 hydrogen-bond acceptors, the Crippen calculated partition coefficient is logP ≈ 0.81 and the calculated molar refractivity is 20.46 cm³ mol⁻¹. A logP in this range means the molecule is amphiphilic enough to cross between phases, which is often the useful behaviour in extraction and formulation. PubChem’s curated experimental record adds: Succinonitrile is 50 to 100 mg/mL at 70 °F (NTP, 1992).

2. Succinonitrile application: Used in the production of plastics and nitron fibers

PubChem’s use and manufacturing record describes Succinonitrile as follows: Used in the production of plastics and nitron fibers. These applications are what make the polarity question practical — solvent choice, extraction recovery, cleaning and formulation all turn on how strongly the molecule interacts with polar phases.

The measured physical behaviour recorded for this substance is consistent with that picture. Solubility: 50 to 100 mg/mL at 70 °F (NTP, 1992). Physical Description: Succinonitrile appears as colorless to light brown crystals.. Density: 1.023 at 113 °F (NTP, 1992) - Denser than water;. Melting Point: 135 to 136 °F (NTP, 1992). These are database values and should be read with the conditions (temperature, purity, pressure) that the source states.

No dilute-gas permittivity is reported here: the Debye estimate would have to inherit a dipole moment that this method does not deliver reliably for this class of compound (the method over-estimates nitriles (mean error +0.61 D over three benchmark nitriles)), and for an ionic substance the equation does not apply at all.

Structurally the reactivity sits in 2 × nitrile (–C≡N). That functional inventory, together with the substantial dipole, is what predicts the solubility and adsorption behaviour: polar groups give the molecule a handle on polar solvents and on polar surfaces, while the hydrocarbon portion resists them.

PubChem’s GHS record for this substance lists H302 (95%): Harmful if swallowed [Warning Acute toxicity, oral] and H311 (36.2%): Toxic in contact with skin [Danger Acute toxicity, dermal]. Those classifications, not the polarity of the molecule, normally determine packaging, labelling, ventilation and transport requirements.

Recommended Analytical Quality-Control Strategy

• Identity confirmation: FTIR or Raman against a reference spectrum, supported by GC–MS or LC–MS where the compound is amenable; this is the fastest way to catch a mis-labelled lot.
• Assay / purity: GC-FID or GC-MS for volatile material, HPLC with a validated detector for non-volatile or thermally labile material; state the basis (area %, assay on dried substance, or titrimetric) on the certificate of analysis.
• Water content: Karl Fischer titration is the default for a substance whose polarity and hydrogen-bonding capacity make it hygroscopic; moisture is the single most common cause of out-of-specification lots.
• Related substances: a gradient HPLC or GC method capable of resolving the synthesis by-products and the isomeric impurities typical of this structure.
• Physical constants: density, refractive index and boiling or melting range against the published values — cheap, fast and often sufficient to reject a lot before any chromatographic work is done.

In short, specify Succinonitrile by assay, water content, impurity profile, packaging and transport class, and state the intended application on the enquiry. The polarity analysis above explains behaviour in use; it does not replace a specification.

3. Polarity Comparison: C₄H₄N₂ and Related Industrial Fluids

The comparison below places C₄H₄N₂ next to structurally related substances from the same catalogue. Dipole moments come from one consistent protocol (GFN2-xTB//MMFF94, gas phase, single conformer) and are quoted only where that protocol has been validated; where it has not, the cell says so instead of giving a number. Permittivities are dilute-gas estimates from the Debye equation, logP values are Crippen calculations, and the solubility column is a qualitative inference from the calculated descriptors rather than a measurement.

The spread across this table is the point: composition alone does not set the polarity verdict. C₄H₄N₂ sits where it does because of the balance between its polar functional groups and the asymmetry of its shape, and any of the neighbouring entries can be the better choice once the temperature, the phase and the required polarity window are fixed.

4. Expert R&D Commentary

5. Regulatory, Safety & Sustainability Trends

Regulatory status is specific to the substance and to the jurisdiction, and it changes. For CAS 110-61-2 the authoritative public sources are the ECHA registered-substance database for the EU, and the OSHA and NIOSH tables for occupational exposure in the United States.

PubChem’s GHS record for this substance lists H302 (95%): Harmful if swallowed [Warning Acute toxicity, oral] and H311 (36.2%): Toxic in contact with skin [Danger Acute toxicity, dermal]. These statements are the ones that must appear on the label and in section 2 of the safety data sheet; they, rather than the polarity of the molecule, drive classification, packaging group and transport documentation.

No occupational exposure limit for this substance is quoted in this article, because none was present in the database record used here. Publishing a limit that is not on the record would be worse than publishing none: obtain the applicable value from the OSHA Z-table, the NIOSH pocket guide or the equivalent national instrument before designing the ventilation or monitoring programme.

From a compliance and sustainability standpoint, the polarity of C₄H₄N₂ is a means rather than an end. It determines which solvent can replace another, how completely the substance can be recovered from a stream, and how much energy the separation will cost — so it belongs in the process justification, while the hazard classification and the exposure limits belong in the safety case.

6. Guidechem's Procurement Tips: What to Specify for Succinonitrile

A purchase enquiry for Succinonitrile (CAS 110-61-2) should state the grade, assay basis, permitted impurity limits, water content, packaging, and the transport and regulatory status required for the destination market. Where the substance is used as a reagent or intermediate, the impurity profile usually matters more than the nominal percentage.

Because polarity governs phase behaviour, it also governs recovery: a substantial molecule is easier to strip from a non-polar stream and harder to dry than a non-polar one, and vice versa. Confirm the Guidechem supply listing for current availability and compare lots on the certificate of analysis rather than on the label alone.

Frequently Asked Questions (FAQs)

References & Academic Databases

1. PubChem Compound Summary: Succinonitrile, CAS RN 110-61-2, CID 8062. National Center for Biotechnology Information. pubchem.ncbi.nlm.nih.gov
2. ECHA Substance Information: Succinonitrile, CAS 110-61-2 — REACH registration status, harmonised classification and regulatory context. European Chemicals Agency.
3. NIST Chemistry WebBook / CCCBDB: experimental geometry, vibrational data and dipole-moment compilations for Succinonitrile. National Institute of Standards and Technology.
4. CRC Handbook of Chemistry and Physics, 92nd ed. (Haynes, W. M., ed.), CRC Press, 2011 — electronegativity, dielectric constant and dipole-moment tables.
5. Nelson, R. D.; Lide, D. R.; Maryott, A. A.: Selected Values of Electric Dipole Moments for Molecules in the Gas Phase, NSRDS-NBS 10, National Bureau of Standards, 1967.
6. Snyder, L. R.: solvent-polarity classification and the P′ scale for liquid chromatographic solvents. The P′ scale is defined only for conventional liquid solvents and is not assigned to substances outside that scope.
7. Bannwarth, C.; Ehlert, S.; Grimme, S.: GFN2-xTB — an accurate and broadly parametrised self-consistent tight-binding quantum chemical method with multipole electrostatics and density-dependent dispersion contributions. J. Chem. Theory Comput. 2019, 15 (3), 1652–1671.
8. RDKit / Halgren, T. A.: MMFF94 force field for geometry generation (J. Comput. Chem. 1996, 17, 490–519) and the RDKit cheminformatics toolkit used for the Crippen logP, TPSA and hydrogen-bond descriptors quoted here.