Sodium hydride Polarity

Is NaH (Sodium hydride) Polar or Nonpolar? Molecular Polarity & Structure Analysis

Figure 1: 2D Lewis Structure (NaH)

Polarity Parameters of NaH

CAS Registry Number	7646-69-7
Molecular Formula	NaH
Molecular Weight	23.9977 g/mol
Valence Electrons	2
Lewis Structure Guide	View NaH Lewis Structure Guide
Dipole Moment (μ)	Not defined — ionic / multi-component substance; polarity is described through ionicity and solvation rather than a molecular dipole
Dielectric Constant (εr)	Not quoted — the Debye estimate would inherit a dipole that this method does not deliver reliably for this class of compound
Snyder Polarity Index (P′)	Not conventionally assigned
XlogP3-AA	Not computed (Crippen parameters do not cover every element here) (computed descriptor)

Note: Snyder P′ is a chromatographic solvent scale developed for conventional liquid solvents; the value shown for the dipole is a single-ion-pair calculation about the centre of mass and is origin-dependent for a charged species; XlogP is a calculated partition descriptor, not a direct measure of solvent polarity.

1. Molecular Polarity Analysis of Sodium hydride: Geometry & Dipole Vector

To determine whether Sodium hydride (NaH) is polar or nonpolar, the decisive question is whether the bond dipoles of the molecule cancel once its three-dimensional shape is taken into account. Sodium hydride is an inorganic compound. As set out in the NaH Lewis Structure Guide, NaH has 1 heavy atom.

The bond polarities follow from electronegativity. Because the substance separates into ions, the molecule is polar but the magnitude of its dipole is not quoted here, because the species is ionic or carries a net charge, so the dipole depends on the choice of origin and is not a molecular constant.

For formulation and process work, the useful consequences are these: the calculated topological polar surface area is 0.0 Ų, 0 hydrogen-bond donors and 0 hydrogen-bond acceptors and the Crippen partition coefficient is not quoted, because the parameter set does not cover every element in the molecule.

2. Sodium hydride: Industrial Use, Handling and Specification

Sodium hydride (CAS 7646-69-7) is an inorganic compound, supplied as an industrial chemical. Its polarity matters for the same reason it matters for any substance of this class: it decides which phases the material will enter, how strongly it adsorbs onto polar surfaces, and how much energy a separation will cost.

No fully curated experimental solubility or density value was retrieved for this substance from the public record used here, so the discussion below stays with calculated descriptors rather than quoting a measurement that cannot be verified. On those descriptors the compound presents 0.0 Ų of polar surface area with 0 hydrogen-bond sites.

No dilute-gas permittivity is reported here: the Debye estimate would have to inherit a dipole moment that this method does not deliver reliably for this class of compound (the species is ionic or carries a net charge, so the dipole depends on the choice of origin and is not a molecular constant), and for an ionic substance the equation does not apply at all.

The structure carries no strongly polar functional group, so the intermolecular forces are dominated by dispersion rather than by dipole–dipole attraction or hydrogen bonding.

No GHS hazard statements were retrieved for this substance from the public record used here, so no classification is asserted. The applicable classification must be taken from the supplier’s safety data sheet and from the ECHA or OSHA/NIOSH tables for CAS 7646-69-7.

Recommended Analytical Quality-Control Strategy

• Identity confirmation: FTIR or Raman against a reference spectrum, supported by GC–MS or LC–MS where the compound is amenable; this is the fastest way to catch a mis-labelled lot.
• Assay / purity: GC-FID or GC-MS for volatile material, HPLC with a validated detector for non-volatile or thermally labile material; state the basis (area %, assay on dried substance, or titrimetric) on the certificate of analysis.
• Water content: Karl Fischer titration is the default for a substance whose polarity and hydrogen-bonding capacity make it hygroscopic; moisture is the single most common cause of out-of-specification lots.
• Inorganic / ionic content: ion chromatography or ICP-OES for the counter-ion and for trace metals; for salts the counter-ion stoichiometry is part of the assay, not an afterthought.
• Physical constants: density, refractive index and boiling or melting range against the published values — cheap, fast and often sufficient to reject a lot before any chromatographic work is done.

In short, specify Sodium hydride by assay, water content, impurity profile, packaging and transport class, and state the intended application on the enquiry. The polarity analysis above explains behaviour in use; it does not replace a specification.

3. Polarity Comparison: NaH and Related Industrial Fluids

The comparison below places NaH next to structurally related substances from the same catalogue. Dipole moments come from one consistent protocol (GFN2-xTB//MMFF94, gas phase, single conformer) and are quoted only where that protocol has been validated; where it has not, the cell says so instead of giving a number. Permittivities are dilute-gas estimates from the Debye equation, logP values are Crippen calculations, and the solubility column is a qualitative inference from the calculated descriptors rather than a measurement.

The spread across this table is the point: composition alone does not set the polarity verdict. NaH sits where it does because of the balance between weak dispersion forces and the asymmetry of its shape, and any of the neighbouring entries can be the better choice once the temperature, the phase and the required polarity window are fixed.

4. Expert R&D Commentary

5. Regulatory, Safety & Sustainability Trends

Regulatory status is specific to the substance and to the jurisdiction, and it changes. For CAS 7646-69-7 the authoritative public sources are the ECHA registered-substance database for the EU, and the OSHA and NIOSH tables for occupational exposure in the United States.

No GHS hazard statements for this substance were retrieved from the public database used to build this article, so none are asserted here. Treat the absence of a quoted classification as an instruction to check the supplier’s safety data sheet, not as evidence that the substance is harmless.

No occupational exposure limit for this substance is quoted in this article, because none was present in the database record used here. Publishing a limit that is not on the record would be worse than publishing none: obtain the applicable value from the OSHA Z-table, the NIOSH pocket guide or the equivalent national instrument before designing the ventilation or monitoring programme.

From a compliance and sustainability standpoint, the polarity of NaH is a means rather than an end. It determines which solvent can replace another, how completely the substance can be recovered from a stream, and how much energy the separation will cost — so it belongs in the process justification, while the hazard classification and the exposure limits belong in the safety case.

6. Guidechem's Procurement Tips: What to Specify for Sodium hydride

A purchase enquiry for Sodium hydride (CAS 7646-69-7) should state the grade, assay basis, permitted impurity limits, water content, packaging, and the transport and regulatory status required for the destination market. Where the substance is used as a reagent or intermediate, the impurity profile usually matters more than the nominal percentage.

Because polarity governs phase behaviour, it also governs recovery: a polar molecule is easier to strip from a non-polar stream and harder to dry than a non-polar one, and vice versa. Confirm the Guidechem supply listing for current availability and compare lots on the certificate of analysis rather than on the label alone.

Frequently Asked Questions (FAQs)

References & Academic Databases

1. PubChem Compound Summary: Sodium hydride, CAS RN 7646-69-7, CID 24758. National Center for Biotechnology Information. pubchem.ncbi.nlm.nih.gov
2. ECHA Substance Information: Sodium hydride, CAS 7646-69-7 — REACH registration status, harmonised classification and regulatory context. European Chemicals Agency.
3. NIST Chemistry WebBook / CCCBDB: experimental geometry, vibrational data and dipole-moment compilations for Sodium hydride. National Institute of Standards and Technology.
4. CRC Handbook of Chemistry and Physics, 92nd ed. (Haynes, W. M., ed.), CRC Press, 2011 — electronegativity, dielectric constant and dipole-moment tables.
5. Nelson, R. D.; Lide, D. R.; Maryott, A. A.: Selected Values of Electric Dipole Moments for Molecules in the Gas Phase, NSRDS-NBS 10, National Bureau of Standards, 1967.
6. Snyder, L. R.: solvent-polarity classification and the P′ scale for liquid chromatographic solvents. The P′ scale is defined only for conventional liquid solvents and is not assigned to substances outside that scope.
7. Bannwarth, C.; Ehlert, S.; Grimme, S.: GFN2-xTB — an accurate and broadly parametrised self-consistent tight-binding quantum chemical method with multipole electrostatics and density-dependent dispersion contributions. J. Chem. Theory Comput. 2019, 15 (3), 1652–1671.
8. RDKit / Halgren, T. A.: MMFF94 force field for geometry generation (J. Comput. Chem. 1996, 17, 490–519) and the RDKit cheminformatics toolkit used for the Crippen logP, TPSA and hydrogen-bond descriptors quoted here.