Nitric acid Polarity

Is HNO₃ (Nitric acid) Polar or Nonpolar? Molecular Polarity & Structure Analysis

Figure 1: 2D Lewis Structure (HNO ₃; trigonal planar nitrogen centre)

Polarity Parameters of HNO₃

CAS Registry Number	7697-37-2
Molecular Formula	HNO3
Molecular Weight	63.013 g/mol
Valence Electrons	24
Lewis Structure Guide	View HNO3 Lewis Structure Guide
Dipole Moment (μ)	Non-zero; no magnitude is quoted because the method is not validated for small inorganic species of this type
Dielectric Constant (εr)	Not quoted — the Debye estimate would inherit a dipole that this method does not deliver reliably for this class of compound
Snyder Polarity Index (P′)	Not conventionally assigned
XlogP3-AA	-0.35 (Crippen calculated, RDKit) (computed descriptor)

Note: Snyder P′ is a chromatographic solvent scale developed for conventional liquid solvents; no dipole magnitude is quoted: the method is not validated for small inorganic species of this type, so the polarity verdict rests on symmetry and structure alone; no relative permittivity is quoted, because the Debye estimate would inherit an unreliable dipole; XlogP is a calculated partition descriptor, not a direct measure of solvent polarity.

1. Molecular Polarity Analysis of Nitric acid: Geometry & Dipole Vector

To determine whether Nitric acid (HNO₃) is polar or nonpolar, the decisive question is whether the bond dipoles of the molecule cancel once its three-dimensional shape is taken into account. Nitric acid is an inorganic compound. As set out in the HNO₃ Lewis Structure Guide, HNO₃ has 4 heavy atoms. Manufacture of inorganic and organic nitrates and nitro compounds for fertilizers, dye intermediates, explosives ....

The bond polarities follow from electronegativity. The largest differences in the structure are N–O (ΔEN ≈ 0.40), so electron density is pulled toward oxygen. In three dimensions, the nitrogen centre is trigonal planar with sp2 hybridization and bond angles close to 120°. Oxygen retains 2 non-bonding electron pairs. As a result, the molecule is polar but the magnitude of its dipole is not quoted here, because the method is not validated for small inorganic species of this type.

For formulation and process work, the useful consequences are these: the calculated topological polar surface area is 63.4 Ų, 1 hydrogen-bond donor and 2 hydrogen-bond acceptors, the Crippen calculated partition coefficient is logP ≈ -0.35 and the calculated molar refractivity is 8.78 cm³ mol⁻¹. A negative logP indicates a net preference for the aqueous phase over octanol, which is what one expects when polar and ionisable groups dominate a small molecule. PubChem’s curated experimental record adds: Nitric acid is Miscible (NIOSH, 2024).

2. Nitric acid application: Manufacture of inorganic and organic nitrates and nitro compounds for…

PubChem’s use and manufacturing record describes Nitric acid as follows: Manufacture of inorganic and organic nitrates and nitro compounds for fertilizers, dye intermediates, explosives ... These applications are what make the polarity question practical — solvent choice, extraction recovery, cleaning and formulation all turn on how strongly the molecule interacts with polar phases.

The measured physical behaviour recorded for this substance is consistent with that picture. Solubility: Miscible (NIOSH, 2024). Physical Description: Nitric acid, other than red fuming appears as a pale yellow to reddish brown liquid with reddish brown vapors and a suffocating odor.. Density: 1.5 at 77 °F (NIOSH, 2024) - Denser than water;. Melting Point: -44 °F (NIOSH, 2024). These are database values and should be read with the conditions (temperature, purity, pressure) that the source states.

No dilute-gas permittivity is reported here: the Debye estimate would have to inherit a dipole moment that this method does not deliver reliably for this class of compound (the method is not validated for small inorganic species of this type), and for an ionic substance the equation does not apply at all.

The structure carries no strongly polar functional group, so the intermolecular forces are dominated by dispersion rather than by dipole–dipole attraction or hydrogen bonding.

PubChem’s GHS record for this substance lists H272: May intensify fire; oxidizer [Danger Oxidizing liquids; Oxidizing solids] and H314: Causes severe skin burns and eye damage [Danger Skin corrosion/irritation]. Those classifications, not the polarity of the molecule, normally determine packaging, labelling, ventilation and transport requirements.

Recommended Analytical Quality-Control Strategy

• Identity confirmation: FTIR or Raman against a reference spectrum, supported by GC–MS or LC–MS where the compound is amenable; this is the fastest way to catch a mis-labelled lot.
• Assay / purity: GC-FID or GC-MS for volatile material, HPLC with a validated detector for non-volatile or thermally labile material; state the basis (area %, assay on dried substance, or titrimetric) on the certificate of analysis.
• Water content: Karl Fischer titration is the default for a substance whose polarity and hydrogen-bonding capacity make it hygroscopic; moisture is the single most common cause of out-of-specification lots.
• Related substances: a gradient HPLC or GC method capable of resolving the synthesis by-products and the isomeric impurities typical of this structure.
• Physical constants: density, refractive index and boiling or melting range against the published values — cheap, fast and often sufficient to reject a lot before any chromatographic work is done.

In short, specify Nitric acid by assay, water content, impurity profile, packaging and transport class, and state the intended application on the enquiry. The polarity analysis above explains behaviour in use; it does not replace a specification.

3. Polarity Comparison: HNO₃ and Related Industrial Fluids

The comparison below places HNO₃ next to structurally related substances from the same catalogue. Dipole moments come from one consistent protocol (GFN2-xTB//MMFF94, gas phase, single conformer) and are quoted only where that protocol has been validated; where it has not, the cell says so instead of giving a number. Permittivities are dilute-gas estimates from the Debye equation, logP values are Crippen calculations, and the solubility column is a qualitative inference from the calculated descriptors rather than a measurement.

The spread across this table is the point: composition alone does not set the polarity verdict. HNO₃ sits where it does because of the balance between weak dispersion forces and the asymmetry of its shape, and any of the neighbouring entries can be the better choice once the temperature, the phase and the required polarity window are fixed.

4. Expert R&D Commentary

5. Regulatory, Safety & Sustainability Trends

Regulatory status is specific to the substance and to the jurisdiction, and it changes. For CAS 7697-37-2 the authoritative public sources are the ECHA registered-substance database for the EU, and the OSHA and NIOSH tables for occupational exposure in the United States.

PubChem’s GHS record for this substance lists H272: May intensify fire; oxidizer [Danger Oxidizing liquids; Oxidizing solids] and H314: Causes severe skin burns and eye damage [Danger Skin corrosion/irritation]. These statements are the ones that must appear on the label and in section 2 of the safety data sheet; they, rather than the polarity of the molecule, drive classification, packaging group and transport documentation.

No occupational exposure limit for this substance is quoted in this article, because none was present in the database record used here. Publishing a limit that is not on the record would be worse than publishing none: obtain the applicable value from the OSHA Z-table, the NIOSH pocket guide or the equivalent national instrument before designing the ventilation or monitoring programme.

From a compliance and sustainability standpoint, the polarity of HNO₃ is a means rather than an end. It determines which solvent can replace another, how completely the substance can be recovered from a stream, and how much energy the separation will cost — so it belongs in the process justification, while the hazard classification and the exposure limits belong in the safety case.

6. Guidechem's Procurement Tips: What to Specify for Nitric acid

A purchase enquiry for Nitric acid (CAS 7697-37-2) should state the grade, assay basis, permitted impurity limits, water content, packaging, and the transport and regulatory status required for the destination market. Where the substance is used as a reagent or intermediate, the impurity profile usually matters more than the nominal percentage.

Because polarity governs phase behaviour, it also governs recovery: a polar molecule is easier to strip from a non-polar stream and harder to dry than a non-polar one, and vice versa. Confirm the Guidechem supply listing for current availability and compare lots on the certificate of analysis rather than on the label alone.

Frequently Asked Questions (FAQs)

References & Academic Databases

1. PubChem Compound Summary: Nitric acid, CAS RN 7697-37-2, CID 944. National Center for Biotechnology Information. pubchem.ncbi.nlm.nih.gov
2. ECHA Substance Information: Nitric acid, CAS 7697-37-2 — REACH registration status, harmonised classification and regulatory context. European Chemicals Agency.
3. NIST Chemistry WebBook / CCCBDB: experimental geometry, vibrational data and dipole-moment compilations for Nitric acid. National Institute of Standards and Technology.
4. CRC Handbook of Chemistry and Physics, 92nd ed. (Haynes, W. M., ed.), CRC Press, 2011 — electronegativity, dielectric constant and dipole-moment tables.
5. Nelson, R. D.; Lide, D. R.; Maryott, A. A.: Selected Values of Electric Dipole Moments for Molecules in the Gas Phase, NSRDS-NBS 10, National Bureau of Standards, 1967.
6. Snyder, L. R.: solvent-polarity classification and the P′ scale for liquid chromatographic solvents. The P′ scale is defined only for conventional liquid solvents and is not assigned to substances outside that scope.
7. Bannwarth, C.; Ehlert, S.; Grimme, S.: GFN2-xTB — an accurate and broadly parametrised self-consistent tight-binding quantum chemical method with multipole electrostatics and density-dependent dispersion contributions. J. Chem. Theory Comput. 2019, 15 (3), 1652–1671.
8. RDKit / Halgren, T. A.: MMFF94 force field for geometry generation (J. Comput. Chem. 1996, 17, 490–519) and the RDKit cheminformatics toolkit used for the Crippen logP, TPSA and hydrogen-bond descriptors quoted here.